ASTM D2996 FREE DOWNLOAD

This specification covers machine-made reinforced thermosetting resin pressure pipe RTRP manufactured by the filament winding process. Illinois Illinois - Chicago. NOTE 4—For the purposes of this standard, polymer does not include natural polymers. This standard has been approved for use by agencies of the Department of Defense. Materials shall be tested and the individual grades shall conform to the specified values of dimensions and tolerances, long-term static hydrostatic strength, long-term cyclic hydrostatic strength, short-term hydrostatic failure strength, longitudinal tensile properties, and stiffness factor. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Use on a local area network or other network is not permitted.

Uploader:	Kagarr
Date Added:	18 June 2013
File Size:	66.88 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	13953
Price:	Free* [*Free Regsitration Required]

This standard does not purport to address all of the safety problems, if any, associated with its use. Additionally, the pipe shall meet the applicable cell limit requirements d299 short-term rupture strength, longitudinal tensile strength, longitudinal tensile modulus, and apparent stiffness factor as described in Table 2 when tested in accordance with 8. Florida Florida Codes 6th ed.

ASTM D2996

Skip to the beginning of the images gallery. For the purposes of this standard, polymer does not include natural polymers. Link to Active This link will always route to the current Active version of the standard. This standard does not purport to address all of the safety problems, if any, associated with its use.

This specification covers machine-made reinforced thermosetting resin pressure pipe RTRP manufactured by the filament winding process.

In addition, a secondary cell classification system defines the basic mechanical properties of the pipe. Type of end closure used, that is, free or restrained should be indicated on certi?

ASTM D2996 STANDARD FOR FILAMENT-WOUND FIBERGLASS PIPE

NOTE 4—For the purposes of this standard, polymer does not include natural polymers. Included are a classification system and requirements for materials, mechanical properties, dimensions, performance, methods of test, and marking. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This specification covers only reinforced thermosetting resin pipe RTRP. Link to Active This link will always route to the current Active version of the standard.

The pipe shall be round and straight and the bore of the pipe shall be smooth and uniform. The pipes are generally classified by type, grade, class, and hydrostatic design. Note 2—This specification is applicable to RTRP where the ratio of outside diameter to wall thickness is It is obtained by multiplying the hydrostatic design basis as determined by Procedure A or Procedure B by the service design factor.

Energy Energy References Inspection. In Method D either Procedure A, using data obtained in accordance with Test Method Dor Procedure B, using data obtained in accordance with Test Method Dis used to determine the estimated long-term hydrostatic strength.

In addition, a secondary cell classification system defines the basic mechanical properties of the pipe.

ASTM D Specs - Beetle Plastics

A superscript epsilon e indicates x2996 editorial change since the last revision or reapproval. We recommend users of early versions of Internet Explorer to update to Version 11 or later. Last previous edition D — Active view current version of standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

JavaScript seems to be disabled in your browser. This strength in the wall of the pipe is equal to the circumferential stress due to internal hydrostatic pressure that will fail the pipe when extrapolated to 3 pressure cycles Procedure A or to h under continuously applied pressure Procedure B. Historical Version s - view previous versions of standard. d2996

There is no known ISO equivalent to this standard. The service design factor should be selected by the design engineer after fully evaluating the service conditions and the engineering properties of the speci?

The values given in parentheses are provided for information purposes only. A number in parentheses indicates the year of last reapproval. All pipe ends shall be cut at right angles to the axis of the pipe and any sharp edges removed.